Netgear extender setup

Should I Reconfigure Netgear Extender If I Replaced My Router

People set up Netgear wireless extenders in their homes to access flawless internet. Netgear extenders amplify the WiFi signals of the router to provide large internet coverage. However, many users have raised the question that should they reconfigure their Netgear extender if they replaced the router. If you are also looking for an answer to same question, it is yes. You need to perform Netgear extender setup if you have replaced your router. But, before this, you need to reset your extender. So, let’s discuss the steps to reset your Netgear extender.

How to Reset Netgear Wireless Extender?

Follow the steps given below to restore your WiFi device to its factory default settings:

  • Ensure that the power LED on your extender is stable.

  • Now, pick a paper clip or an oil pin.

  • Press the Reset button on your extender.

  • As soon as you release the button, your Netgear extender will get restored to its initial settings.

Now that your WiFi device has been restored to the default mode, you are ready to perform new extender setup.

Steps to Configure Netgear Extender

  1. Power Up Your Netgear Extender

  • Connect your Netgear extender to a power source.

  • Switch on the Power button.

  • Let your WiFi extender boot up properly.

  1. Connect Your WiFi Devices

  • Now, grab an Ethernet cable.

  • Connect one end of the Ethernet cable to the Netgear extender and another to the router.

  1. Switch On Your PC

  • Once your Netgear extender and router are connected properly, turn on your PC.

  • Open a web browser.

  • Move the cursor to the address bar of your web browser.

  • Type the default IP address in it.

  • Press the Enter key.

Note: Access the mywifiext local page to configure your Netgear extender if you are using an Apple device.

  1. Log in to Your Netgear Extender

  • You will be prompted to log in to your Netgear wireless range extender.

  • Provide the default login credentials of your Netgear extender.

  • Once done, click the Log In button.

  1. Netgear Genie Setup Wizard

  • The Netgear Genie setup wizard will appear.

  • Follow the on-screen commands and complete performing Netgear extender setup.

In this way, you can reconfigure your Netgear wireless extender if you have replaced your router.

Since, the Netgear extender can be easily reconfigured with the help of the aforementioned guide still, some users face issues while doing so. Therefore, here’s a list of points to remember while reconfiguring your Netgear extender to avoid any problem.

Points to Remember While Reconfiguring Your Extender

  • Always plug your Netgear extender into a working wall socket. In addition, you can use a UPS to protect your WiFi device from power outages.

  • Do not proceed with the Netgear extender setup process until the power LED on your extender becomes steady.

  • For a hardwired connection between your extender and router, use a damage-free Ethernet cable.

  • The web browser you are using to reconfigure your extender should be updated. Also, remember to clear its cookies, cache, and browsing history by navigating to its settings.

  • Make sure that your Netgear extender is placed away from devices and transmitting appliances like microwave ovens, cordless phones, baby monitors, refrigerators, etc.

  • Enter the correct default username and password to log in to your WiFi extender. Try to avoid typos as the default login details are case-sensitive. Also, ensure that the Caps Lock key on your keyboard is off while typing the default login credentials.

  • Once you are logged in to your extender, do not refresh your web browser or turn off your WiFi device. This may halt the process of Netgear extender setup.


Let’s hope that now you are aware of the fact that you need to reconfigure your extender after replacing your router. The aforementioned guide will help you in setting up your Netgear WiFi extender successfully.

Comments are closed, but trackbacks and pingbacks are open.